They're made for The Batz Corp. out of Arkansas (imported from Austria).  The
new,
large double enders were even specially made (I think Brownies ordered 1000).  
These
guys make the best in my opinion.

kirvine@sa*.ne* wrote:

> We need to find one that will work for the wreck divers. I checked all
> of mine again and found that I have some very large ones that I got from
> Brownies that have no magnetism anywhere. They have huge loops as well
> so will fit the mit finger. I will take them back over to Brownies so
> they can identify them. They still have the tags on them.
>
> Jim Cobb wrote:
> >
> > George the MC ones are slightly magnetic, and there are some rust stains
> > around the snap. Like I said I have not experienced a failure so far, but
> > then I do rinse them off after a dive and lube them regularly. All all my
> > diving is in salt water so I have to take extra precautions against
> > corrosion problems.
> >
> >  Jim
> >
> > Sender: kirvine@sa*.ne*  Date: 7/4/99 10:23 AM
> >
> > >I went back and checked my snaps with a magnet. The $13 giant snaps will
> > >not pick up the tiny magnet. The $8 ones do. The tiny ones from
> > >Brownies, like for backup lights and long hoses, have no magnetism at
> > >all. By the way, I was testing snaps that I have in a collection that
> > >are not on my gear. The ones on my gear are very old and I got them from
> > >a yacht suplly store which is no longer in business, and they were
> > >unable to order the ones I wanted as of about seven years ago. I try
> > >every one I see trying to find the best ones. So far some are from
> > >Brownies, some from a hardware store in Lauderdale by the Sea.
> > >
> > >I always check the stuff out of habit due ot the scooter building. I
> > >frequently get bullshit stainless snuck in on me, and just take it back
> > >for replacement. Washers are a big one for this type of corner-cutting.
> > >
> > >It is funny how the smallest detail of dive gear can make or break your
> > >fun.
> > >
> > >To test this stuff otherwise I hang it off the dock on a line for a few
> > >days. The bottom line is that the more the snap attracts money and the
> > >less it attracts magnets the better it is at not rusting. Springs are
> > >the same.
> > >
> > >houdini@gr*.xt*.ne* wrote:
> > >>
> > >> Scott Landon wrote:
> > >> >
> > >> > unfortuneately, there are quite a few grades of stainless.  and as you
can
> > >> > guess, some grades cost more than others.  i am by no means a
> > metallurgist,
> > >> > but i have installed my share of piping in corrosive service in a
chemical
> > >> > plant.  a 316 grade would be ideal.
> > >> >
> > >> > scott
> > >> >
> > >> > >From: Mike Rodriguez <mikey@ma*.co*>
> > >> > >To: Art Greenberg <artg@ec*.ne*>
> > >> > >CC: Cavers <cavers@cavers.com>, Techdiver <techdiver@aq*.co*>
> > >> > >Subject: Re: Stainless Steel Bolt Snaps
> > >> > >Date: Sat, 03 Jul 1999 19:09:25 -0400
> > >> > >
> > >> > >At 08:08 AM 7/3/99 -0400, Art Greenberg wrote:
> > >> > >
> > >> > > >I've just replaced another large SS bolt snap on my rig. This one
was
> > on
> > >> > > >my primary reel, and I had just replaced that one a week ago!
> > >> > >
> > >> > >I replaced all my brass snaps a few months ago with SS snaps
> > >> > >from Extreme Exposure.  I don't know where they get them, but
> > >> > >they're the best I've ever seen.  They're expensive, but so
> > >> > >far none has shown the slightest trace of corrosion and they
> > >> > >operate very smoothly.  I tried some cheap SS snaps from a
> > >> > >local hardware store and regretted it; now I'll only use the
> > >> > >ones from EE.
> > >> > >
> > >> > >Take a look at:
> > >> > >
> > >> > >http://www.extreme-exposure.com/accessories.shtml
> > >> > >
> > >> > >The small ones seem to be good for just about every application.
> > >> > >
> > >> > >-Mike Rodriguez
> > >> > ><mikey@ma*.co*>
> > >> .....what Scott said, many different grades of stainless. Lower numbers
> > >> usually are tougher, higher numbers are usually more resistant to
> > >> corrosion. What George said about being magnetic is a good indicator. If
> > >> it's magnetic - it's NOT a good grade of stainless. True 304 or 316
> > >> stainless isn't magnetic. (I have found alot of Japaneese stainless is
> > >> magnetic).
> > >> > >
> > >> >
> > >> > _______________________________________________________________
> > >> > Get Free Email and Do More On The Web. Visit http://www.msn.com
> > >
> > >
> > >--
> > >Send mail for the `techdiver' mailing list to `techdiver@aq*.co*'.
> > >Send subscribe/unsubscribe requests to `techdiver-request@aq*.co*'.
> > >
> >
> >  -------------------------------------------------------------------
> >  Learn About Trimix at http://www.cisatlantic.com/trimix/trimix.html

Navigate by Author: [Previous] [Next] [Author Search Index]
Navigate by Subject: [Previous] [Next] [Subject Search Index]

[Send Reply] [Send Message with New Topic]

[Search Selection] [Mailing List Home] [Home]