This is a multi-part message in MIME format. ------=_NextPart_000_02CA_01BE85C5.436CAE00 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Bill What is with you. We do not allow as you accuse.=20 some idiot filled a cylinder labeled as air with a hot mix and left the = air label on it. The diver had been using the same air cylinder all week = as a bailout cylinder and had no reason to think someone would fill it = with a hot mix. =20 If you dived a cylinder yesterday that had air in it and was labeled air = and you left it at for instance at Brownies dive shop would you suspect = overnight someone had changed the mix? =20 As per IANTD mixing standards=20 LABELING BOTTOM MIX EANx MIXTURES WITH LESS THAN 41% OXYGEN a.. Where applicable cylinders must be marked per legal requirements = in addition to the below b.. Cylinders painted yellow must be labeled with a 4 inches (10 = centimeters) green band. The band must wrap around the tank starting at = the flat of the cylinder. The label must state "Enriched Air Nitrox" (or = an applicable acronym). IANTD has EANx decals available for labeling = tanks. c.. Cylinders painted with colors other than yellow require a 6 = inches (15 centimeter) Enriched Air Nitrox band (decal) with the top 1 = inch (2.5 centimeters) and the bottom 1 inch (2.5 centimeters) yellow. = The middle of the band (decal) should be printed with a green background = and the message, "Enriched Air Nitrox" (or an applicable acronym) = printed in yellow for easy identification. d.. Nitrox (EANx) cylinders must have Cylinder Contents Labels = affixed to them. The Contents label must state the oxygen percentage = currently in the cylinder and the Maximum Operating Depth (MOD). The = label must be dated and signed by the person who purchased (or = requested) the mix (verifying he/she confirmed the O2 percentage). 1.. This label may be a separate label, or part of the EANx band. = IANTD has waterproof, reusable Cylinder Contents labels and cylinder = content tape available for order.=20 1.. Nitrox (EANx) cylinders must have a current Visual Inspection = (VIP) decal stated that oxygen-compatible lubricants have been used in = the system (valve, tank neck, and/or cylinder). EANx cylinders used with = EAN 41, or greater, or for direct partial pressure blending use, must = have an Oxygen Service Rated VIP decal. IANTD has VIP decals (which also = cover both tank and valve inspections) available for order. a.. It is recommended that an additional label using one of the = following options be used, these do not replace the requirement for the = wrap around labels I A Decal stating MOD to be placed length wise on the cylinder (IAND = inc./IANTD has these with both a fixed=20 MOD plus blank ones for the user to fill in the MOD, these are blue with = white lettering=20 II The MOD may also be painted on the cylinder III A cylinder wrap suitable for regulator hose storage with the MOD = boldly marked on it may also be used=20 (these are also available through IAND inc. / IANTD D. LABELING EANx AND DECOMPRESSION CYLINDERS (GREATER THAN 40%) AND = OXYGEN (OR MIXTURES GREATER THAN 85% OXYGEN) MIXTURES a.. Cylinders containing EAN 40 to 84 must have either a color-coded = green and white label decal boldly stating, "Decompression Mix EAN* = _____." or they may use the "Breathing Gases Other Than Air" decal that = is red and white. (Note! This decal may be used with any gas mixture as = long as the mix and MOD are filled in) This label must be 10 inches (25 = centimeters) long and 4 inches (10 centimeters) wide. IANTD has Cylinder = Contents labels available for order. * Or, equivalent acronym. These = labels must be wrapped around the cylinder at the flat of the cylinder b.. The decompression cylinder with the highest EANx mixture or = oxygen must have some form of protective mechanism to prevent the diver = from accidentally breathing from it. This may be a cover, bungie wrap or = other suitable means. IAND inc. / IANTD has a protective device = available c.. All decompression cylinders must have a tape or label above the = flat of the cylinder visible to the user with the mix or MOD or both = marked. IAND inc. IANTD has these with pre marked mix and MOD as well as = ones with blank spaces for the user to fill in. d.. Cylinders containing oxygen levels of 85% or greater must adhere = to one of the following: 1.. Be painted either green or white with the word oxygen and MOD 20 = fsw (6 msw) legible 2.. Have a 10 inches (25 centimeters) long by 4 inches (10 = centimeters) wide green adhesive band decal with the word "OXYGEN" and = MOD clearly and prominently printed in white on it. IANTD has waterproof = Oxygen Cylinder Decals available for order. a.. It is recommended that an additional label using one of the = following options, these do not replace the requirement for the wrap = around labels I A Decal stating MOD to be placed length wise on the cylinder (IAND = inc./IANTD has these with both a fixed=20 MOD plus blank ones for the user to fill in the MOD, these are blue with = white lettering=20 II The MOD may also be painted on the cylinder III A cylinder wrap suitable for regulator hose storage with the MOD = boldly marked on it may also be used=20 (these are also available through IAND inc. / IANTD a.. LABELING TRIMIX MIXTURES a.. Cylinders containing Trimix must be labeled with the word, = "Trimix", or "Breathing gas other than air". A Cylinder Contents Label = or tape reflecting the percentages of Oxygen, and Helium must be affixed = to the tank. =20 Respectfully yours, Tom Mount CEO IANTD World HQ http://www.iantd.com Respectfully yours, Tom Mount CEO IANTD World HQ http://www.iantd.com ------=_NextPart_000_02CA_01BE85C5.436CAE00 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable <!DOCTYPE HTML PUBLIC "-//W3C//DTD W3 HTML//EN"> <HTML> <HEAD> <META content=3Dtext/html;charset=3Diso-8859-1 = http-equiv=3DContent-Type> <META content=3D'"MSHTML 4.72.3110.7"' name=3DGENERATOR> </HEAD> <BODY bgColor=3D#ffffff> <DIV> <DIV><FONT color=3D#000000 size=3D2>Bill</FONT></DIV> <DIV><FONT color=3D#000000 size=3D2></FONT><FONT size=3D2>What is with = you. We do not=20 allow as you accuse. </FONT></DIV> <DIV><FONT size=3D2>some idiot filled a cylinder labeled as air with a = hot mix and=20 left the air label on it. The diver had been using the same air cylinder = all=20 week as a bailout cylinder and had no reason to think someone would fill = it with=20 a hot mix.</FONT></DIV> <DIV><FONT size=3D2></FONT> </DIV> <DIV><FONT size=3D2>If you dived a cylinder yesterday that had air in it = and was=20 labeled air and you left it at for instance at Brownies dive shop = would=20 you suspect overnight someone had changed the mix?</FONT></DIV> <DIV><FONT size=3D2></FONT> </DIV> <DIV><FONT color=3D#000000 size=3D2>As per IANTD mixing standards = </FONT></DIV> <DIV><FONT color=3D#000000 size=3D2></FONT><B><FONT face=3D"Arial = Narrow" size=3D4> <P>LABELING BOTTOM MIX EANx MIXTURES WITH LESS THAN 41%=20 OXYGEN</P></B></FONT><FONT face=3D"Arial Narrow" size=3D1> <OL></FONT><FONT face=3D"Arial Narrow" size=3D3> <P align=3Djustify> <LI>Where applicable cylinders must be marked per legal requirements = in=20 addition to the below</LI> <P></P> <P align=3Djustify> <LI>Cylinders painted yellow must be labeled with a 4 inches (10=20 centimeters) green band. The band must wrap around the tank starting = at the=20 flat of the cylinder. The label must state "Enriched Air = Nitrox"=20 (or an applicable acronym). IANTD has EANx decals available for = labeling=20 tanks.</LI> <P></P> <P align=3Djustify> <LI value=3D1>Cylinders painted with colors other than yellow = require a 6=20 inches (15 centimeter) Enriched Air Nitrox band (decal) with the top = 1 inch=20 (2.5 centimeters) and the bottom 1 inch (2.5 centimeters) yellow. = The middle=20 of the band (decal) should be printed with a green background and = the=20 message, "Enriched Air Nitrox" (or an applicable acronym) = printed=20 in yellow for easy identification.</LI> <P></P> <P align=3Djustify> <LI>Nitrox (EANx) cylinders must have Cylinder Contents Labels = affixed to=20 them. The Contents label must state the oxygen percentage currently = in the=20 cylinder and the Maximum Operating Depth (MOD). The label must be = dated and=20 signed by the person who purchased (or requested) the mix (verifying = he/she=20 confirmed the O<SUB>2</SUB> percentage).</LI> <P></P></OL> <OL type=3Da> <P align=3Djustify> <LI>This label may be a separate label, or part of the EANx band. = IANTD has=20 waterproof, reusable Cylinder Contents labels and cylinder content = tape=20 available for order. </LI> <P></P></OL> <OL start=3D4> <P align=3Djustify> <LI>Nitrox (EANx) cylinders must have a current Visual Inspection = (VIP)=20 decal stated that oxygen-compatible lubricants have been used in the = system=20 (valve, tank neck, and/or cylinder). EANx cylinders used with EAN = 41, or=20 greater, or for direct partial pressure blending use, must have an = Oxygen=20 Service Rated VIP decal. IANTD has VIP decals (which also cover both = tank=20 and valve inspections) available for order.</LI> <P></P></OL> <OL type=3Da></FONT><FONT face=3D"Arial Narrow"> <LI>It is recommended that an additional label using one of the = following=20 options be used, <B>these do not replace the requirement for the = wrap around=20 labels</LI></OL> <DIR> <DIR> <DIR></B> <P>I A Decal stating MOD to be placed length wise on the cylinder (IAND=20 inc./IANTD has these with both a fixed </P> <P>MOD plus blank ones for the user to fill in the MOD, these are blue = with=20 white lettering </P> <P>II The MOD may also be painted on the cylinder</P> <P>III A cylinder wrap suitable for regulator hose storage with the MOD = boldly=20 marked on it may also be used </P> <P>(these are also available through IAND inc. / IANTD</P></FONT><FONT=20 face=3D"Arial Narrow" size=3D3> <P align=3Djustify></P></FONT><FONT face=3D"Arial Narrow"> <P> </P></DIR></DIR></DIR></FONT><B><FONT face=3D"Arial Narrow" = size=3D4> <P>D. LABELING EANx AND DECOMPRESSION CYLINDERS (GREATER THAN 40%) AND = OXYGEN=20 (OR MIXTURES GREATER THAN 85% OXYGEN) MIXTURES</P></B></FONT><FONT=20 face=3D"Arial Narrow" size=3D1> <OL></FONT><FONT face=3D"Arial Narrow" size=3D3> <P align=3Djustify> <LI>Cylinders containing EAN 40 to 84 must have either a color-coded = green=20 and white label decal boldly stating, "Decompression Mix EAN*=20 _____." or they may use the "Breathing Gases Other Than = Air"=20 decal that is red and white. (Note! This decal may be used with any = gas=20 mixture as long as the mix and MOD are filled in) This label must be = 10=20 inches (25 centimeters) long and 4 inches (10 centimeters) wide. = IANTD has=20 Cylinder Contents labels available for order. * Or, equivalent = acronym.=20 These labels must be wrapped around the cylinder at the flat of the=20 cylinder</LI> <P></P> <P align=3Djustify> <LI>The decompression cylinder with the highest EANx mixture or = oxygen must=20 have some form of protective mechanism to prevent the diver from=20 accidentally breathing from it. This may be a cover, bungie wrap or = other=20 suitable means. IAND inc. / IANTD has a protective device = available</LI> <P></P> <P align=3Djustify> <LI>All decompression cylinders must have a tape or label above the = flat of=20 the cylinder visible to the user with the mix or MOD or both marked. = IAND=20 inc. IANTD has these with pre marked mix and MOD as well as ones = with blank=20 spaces for the user to fill in.</LI> <P></P> <P align=3Djustify> <LI>Cylinders containing oxygen levels of 85% or greater must adhere = to one=20 of the following:</LI> <P></P></OL> <OL type=3Da> <P align=3Djustify> <LI>Be painted either green or white with the word oxygen and MOD 20 = fsw (6=20 msw) legible</LI> <P></P> <P align=3Djustify> <LI>Have a 10 inches (25 centimeters) long by 4 inches (10 = centimeters) wide=20 green adhesive band decal with the word "OXYGEN" and MOD = clearly=20 and prominently printed in white on it. IANTD has waterproof Oxygen = Cylinder=20 Decals available for order.</LI> <P></P></OL> <OL start=3D5></FONT><FONT face=3D"Arial Narrow"> <LI>It is recommended that an additional label using one of the = following=20 options, <B>these do not replace the requirement for the wrap around = labels</LI></OL> <DIR> <DIR> <DIR></B> <P>I A Decal stating MOD to be placed length wise on the cylinder (IAND=20 inc./IANTD has these with both a fixed </P> <P>MOD plus blank ones for the user to fill in the MOD, these are blue = with=20 white lettering </P> <P>II The MOD may also be painted on the cylinder</P> <P>III A cylinder wrap suitable for regulator hose storage with the MOD = boldly=20 marked on it may also be used </P> <P>(these are also available through IAND inc. / IANTD</P></FONT><FONT=20 face=3D"Arial Narrow" size=3D3> <P align=3Djustify></P></FONT><FONT face=3D"Arial Narrow"> <P> </P></DIR></DIR></DIR> <OL start=3D6 type=3DA></FONT><B><FONT face=3D"Arial Narrow" size=3D4> <LI>LABELING TRIMIX MIXTURES</LI></OL></B></FONT><FONT face=3D"Arial = Narrow"=20 size=3D1> <OL></FONT><FONT face=3D"Arial Narrow" size=3D3> <P align=3Djustify> <LI>Cylinders containing Trimix must be labeled with the word,=20 "Trimix", or "Breathing gas other than air". A = Cylinder=20 Contents Label or tape reflecting the percentages of Oxygen, and = Helium must=20 be affixed to the tank.</LI> <P></P></OL></FONT><FONT face=3D"Arial Narrow"></FONT><FONT = face=3DArial size=3D5> <P></FONT> </P></DIV> <DIV><FONT color=3D#000000 size=3D2><BR>Respectfully yours,<BR>Tom = Mount<BR>CEO=20 IANTD World HQ<BR><A=20 href=3D"http://www.iantd.com">http://www.iantd.com</A><BR></FONT></D IV></= DIV> <DIV><FONT color=3D#000000 size=3D2><BR>Respectfully yours,<BR>Tom = Mount<BR>CEO=20 IANTD World HQ<BR><A=20 href=3D"http://www.iantd.com">http://www.iantd.com</A><BR></FONT></D IV></= BODY></HTML> ------=_NextPart_000_02CA_01BE85C5.436CAE00--
Navigate by Author:
[Previous]
[Next]
[Author Search Index]
Navigate by Subject:
[Previous]
[Next]
[Subject Search Index]
[Send Reply] [Send Message with New Topic]
[Search Selection] [Mailing List Home] [Home]