Brian, The pattern on the sides of the tanks are probably due to the tanks being doubled up and resting flat on the same sides most of the time. Also be careful of bleeding the tanks down too rapidly. If you purge the tanks from time to time, do it slowly. Any condensation build up in the tanks will drip and settle on what ever side happens to be facing down. This will be the side that gets hammered the worst. If you're using DIN, then make sure the threaded cups are free of any moisture by blowing air out before you make the hook up. Blow air out and make sure the fill whips are clean before you make that connection. Tilt the tanks like you described to get the spots on the bottom. Good luck. - JT At 03:04 PM 3/17/99 -0500, you wrote: >>>> <excerpt><fontfamily><param>Fixedsys</param><color><param>0000 ,0000,8080</param><smaller>Yesterday, I brought my PS 104's into my local dive shop to VIP them. Upon looking inside I was shocked. There was alot of rust. It wasn't fine little specs evenly distributed. There were quarter size spots that appeared to be in a pattern. Four of these quarter size spots were in a straight line traveling down the inside wall. There were a few other places with these spots but they weren't as patternized. The spots weren't deep and pitted like I expected. Most of it came off with a few minutes of wire whipping. There were also quite a few spots in the far bottom of the tanks. Both tanks looked about the same. Anyone have any idea what happened from what I have described? The tanks are 3 years old and last year when I looked inside of them....they were pretty clean. </smaller></color></fontfamily> <fontfamily><param>Fixedsys</param><color><param>0000,0000,8080&l t;/param><smaller>I spoke briefly through the shop owner to Bill High the Tank Guy in Seattle. From what I understand, he is the guy who writes the brochures for the cylinder manufactures with respect to routine care, maintance, and warranties. He said it's probably from getting the tanks filled at shops with immersion tubs, and that they probably aren't being careful when filling. The only place I have had my tanks filled at are the North Central Florida shops and the local shop in my area. The local shop in my area has a brand new system with a self purging compressor. I am not sure what name brand it is. </smaller></color></fontfamily> <fontfamily><param>Fixedsys</param><color><param>0000,0000,8080&l t;/param><smaller>Since I have access to a tank tumbler, I'm going to use it. What is commonly put in the tanks for tumbling? The tumbler is at my uncles house and he uses some kind of metal pellets. Have thoughts changed about what to use during the past 20 years? My Uncle is from the Lloyd Bridges days of diving. (: How do I get the spots out from the bottom of the tanks? Should I elevate one end of the tumbler so the abraisant is collected in the bottom of the tanks while they turn? </smaller></color></fontfamily> <fontfamily><param>Fixedsys</param><color><param>0000,0000,8080&l t;/param><smaller>I appreciate your responses and If you have questions...shoot. </smaller></color></fontfamily> <fontfamily><param>Fixedsys</param><color><param>0000,0000,8080&l t;/param><smaller>Brian </smaller></color></fontfamily> <fontfamily><param>Fixedsys</param><color><param>0000,0000,8080&l t;/param><smaller>"Wilderness is not a luxury, but a necessity of the human spirit, and as vital to our lives as water and good bread. A civilization which destorys what little remains of the wild, the spare, the original, is cutting itself off from the origins and betraying the principle of civilization itself." Edward Abby - Desert Solitaire </smaller></color></fontfamily> </excerpt><<<<<<<<
Navigate by Author:
[Previous]
[Next]
[Author Search Index]
Navigate by Subject:
[Previous]
[Next]
[Subject Search Index]
[Send Reply] [Send Message with New Topic]
[Search Selection] [Mailing List Home] [Home]