Mailing List Archive Mailing List Archive
Hello Jim, This valve was a conceptual design. It was designed more for true "modular", reason being that it could be assembled or taken apart without draining the cylinders. Two "Y" cylinders could be assembled into doubles by simply installing the center piece at any time. Both orifices on each valve were 300 bar DIN, as were both ends of the crossbar. You simply shut that valve orifice down in-order to remove the crossbar or isolate the cylinders in case of failure. It did go in our catalog, but I seriously doubt you will ever see it from us. It was too costly in comparison to our stand alone dedicated manifold, which is widely accepted. I doubt the limited demand for such a new and unconventional design would have been worth it. Dell Motes Dive Rite 117 W.Washington St. Lake City, Florida 32055 www.dive-rite.com -----Original Message----- From: Jim Cobb <cobber@ci*.co*> To: trey@ne*.co* <trey@ne*.co*>; Dell Motes <dell@di*.co*> Cc: Mike Bruic <mikebruic@di*.co*>; paul.r.harris@te*.ne* <paul.r.harris@te*.ne*>; 'Chris Elmore' <ElmoreC@gw*.sc*.ed*>; cmilz@Mi*.ED* <cmilz@Mi*.ED*>; techdiver@aquanaut.com <techdiver@aquanaut.com>; cavers@ca*.co* <cavers@ca*.co*> Date: Saturday, May 13, 2000 8:24 AM Subject: Re: AUL canister light / light cord >Hey, Dell, is it DR or OMS that came up with that manifold with 4 knobs? You >know, 2 on each valve and none on the cross tube. If it was DR, are you >serious about this product? Or was this some kind of joke? > > Jim > ------------------------------------------------------------------- > Learn About Trimix at http://www.cisatlantic.com/trimix/ > >> From: trey@ne*.co* (Trey) >> Reply-To: trey@ne*.co* >> Date: Thu, 11 May 2000 10:36:34 -0400 >> To: Dell Motes <dell@di*.co*> >> Cc: Mike Bruic <mikebruic@di*.co*>, paul.r.harris@te*.ne*, "'Chris >> Elmore'" <ElmoreC@gw*.sc*.ed*>, cmilz@Mi*.ED*, techdiver@aquanaut.com, >> cavers@ca*.co* >> Subject: Re: AUL canister light / light cord >> >> Dell, you guys should cater to swimmers - that is about the level one >> needs to be at to by some of your crap - totally obvlivious. >> >> >> Dell Motes wrote: >>> >>> Hardly pissed Mike, I answered your question the first time. >>> All parts are based on margins to support our dealers and international >>> distributors. Thats called business. Thats why we have the widely (world >>> wide) established, long lasting network. I don't care if you lack the >>> intellect to understand that, and you can try to twist it up however you >>> please. >>> Besides, what do you care? I thought you were catering to swimmers and not >>> divers? >>> -----Original Message----- >>> From: Mike Bruic <mikebruic@di*.co*> >>> To: Dell Motes <dell@di*.co*>; paul.r.harris@te*.ne* >>> <paul.r.harris@te*.ne*>; 'Chris Elmore' <ElmoreC@gw*.sc*.ed*>; >>> cmilz@Mi*.ED* <cmilz@Mi*.ED*> >>> Cc: techdiver@aquanaut.com <techdiver@aquanaut.com>; cavers@ca*.co* >>> <cavers@ca*.co*> >>> Date: Thursday, May 11, 2000 8:57 AM >>> Subject: Re: AUL canister light / light cord >>> >>>> Ah..... little dell is all pissed and pouty because he can't answer the >>>> question, maybe you should go check with your daddy (lamar). >>>> >>>> Bruic >>>> >>>> ----- Original Message ----- >>>> From: Dell Motes <dell@di*.co*> >>>> To: Mike Bruic <mikebruic@di*.co*>; <paul.r.harris@te*.ne*>; >>> 'Chris >>>> Elmore' <ElmoreC@gw*.sc*.ed*>; <cmilz@Mi*.ED*> >>>> Cc: <techdiver@aquanaut.com>; <cavers@ca*.co*> >>>> Sent: Thursday, May 11, 2000 8:57 AM >>>> Subject: Re: AUL canister light / light cord >>>> >>>> >>>>> Now I'm a moron ? >>>>> Your a real class act, Bruic. >>>>> You need to go back to scamming college girls into your porn "calendar". >>>>> Yep, a real class guy. >>>>> >>>>> -----Original Message----- >>>>> From: Mike Bruic <mikebruic@di*.co*> >>>>> To: Dell Motes <dell@di*.co*>; paul.r.harris@te*.ne* >>>>> <paul.r.harris@te*.ne*>; 'Chris Elmore' <ElmoreC@gw*.sc*.ed*>; >>>>> cmilz@Mi*.ED* <cmilz@Mi*.ED*> >>>>> Cc: techdiver@aquanaut.com <techdiver@aquanaut.com>; cavers@ca*.co* >>>>> <cavers@ca*.co*> >>>>> Date: Thursday, May 11, 2000 8:32 AM >>>>> Subject: Re: AUL canister light / light cord >>>>> >>>>> >>>>>> Yea, that is correct, she charged a dollar more for the precision bore >>>>>> glass, now were at $4.00 a tube. "Optically correct"??? What kind of >>> bull >>>>>> shit is this, I don't use them to read with you moron, and it sure as >>>> hell >>>>>> doesn't justify the price reaming your giving your customers on this. >>>>>> >>>>>> Bruic >>>>>> >>>>>> ----- Original Message ----- >>>>>> From: Dell Motes <dell@di*.co*> >>>>>> To: Mike Bruic <mikebruic@di*.co*>; <paul.r.harris@te*.ne*>; >>>>> 'Chris >>>>>> Elmore' <ElmoreC@gw*.sc*.ed*>; <cmilz@Mi*.ED*> >>>>>> Cc: <techdiver@aquanaut.com>; <cavers@ca*.co*> >>>>>> Sent: Thursday, May 11, 2000 8:18 AM >>>>>> Subject: Re: AUL canister light / light cord >>>>>> >>>>>> >>>>>>> Sure Mike, the ones you showed us were not precision bore glass, flame >>>>>>> polished or optically correct. They didn't meet our specs. >>>>>>> You get what you pay for. >>>>>>> ta,ta >>>>>>> Dell Motes >>>>>>> Dive Rite >>>>>>> 117 W.Washington St. >>>>>>> Lake City, Florida 32055 >>>>>>> www.dive-rite.com >>>>>>> >>>>>>> -----Original Message----- >>>>>>> From: Mike Bruic <mikebruic@di*.co*> >>>>>>> To: Dell Motes <dell@di*.co*>; paul.r.harris@te*.ne* >>>>>>> <paul.r.harris@te*.ne*>; 'Chris Elmore' <ElmoreC@gw*.sc*.ed*>; >>>>>>> cmilz@Mi*.ED* <cmilz@Mi*.ED*> >>>>>>> Cc: techdiver@aquanaut.com <techdiver@aquanaut.com>; cavers@ca*.co* >>>>>>> <cavers@ca*.co*> >>>>>>> Date: Wednesday, May 10, 2000 10:16 PM >>>>>>> Subject: Re: AUL canister light / light cord >>>>>>> >>>>>>> >>>>>>>> Dell, can you please explain to "all" members of this list why a test >>>>>> tube >>>>>>>> from Dive Right cost around $30.00, when I showed you guys where to >>>> get >>>>>>> them >>>>>>>> custom made for less than $3.00 ea. That's one hell of a mark-up if >>>> you >>>>>>> ask >>>>>>>> me. >>>>>>>> >>>>>>>> Bruic >>>>>>>> >>>>>>>> >>>>>>>> ----- Original Message ----- >>>>>>>> From: Dell Motes <dell@di*.co*> >>>>>>>> To: <paul.r.harris@te*.ne*>; 'Chris Elmore' <ElmoreC@gw*.sc*.ed*>; >>>>>>>> <cmilz@Mi*.ED*> >>>>>>>> Cc: <techdiver@aquanaut.com>; <cavers@ca*.co*> >>>>>>>> Sent: Wednesday, May 10, 2000 12:57 PM >>>>>>>> Subject: Re: AUL canister light / light cord >>>>>>>> >>>>>>>> >>>>>>>>> Depending on the test tube light design, there are a few ways to >>>>>> prevent >>>>>>>>> lens loss. >>>>>>>>> First, don't lubricate the o-rings, simply wet them (very lightly) >>>>> when >>>>>>>>> installing the lens. Lubrication makes them way too easy to pop off >>>>>> when >>>>>>>>> hot, the pressure pushes them right of the end. The slight moisture >>>>>> will >>>>>>>> dry >>>>>>>>> quickly and never be seen again. >>>>>>>>> Relieving the pressure while pressing the lens in place can be done >>>> in >>>>>> a >>>>>>>>> couple of ways. If it has an easily loosened compression type >>>> sealing >>>>>>>> gland >>>>>>>>> on the cord, just back off the nut (not the gland itself, use two >>>>>>>> wrenches) >>>>>>>>> and wiggle the cord. This will allow air to escape out around the >>>> cord >>>>>>>> while >>>>>>>>> the lens is being pushed on. Once the lens is in place, re-tighten >>>> the >>>>>>> nut >>>>>>>>> on the gland. If the gland is not accessible, (or easily loosened), >>>>> you >>>>>>>> can >>>>>>>>> "vacuum seal" the lens in place. Place the head on a flat surface >>>> and >>>>>>> push >>>>>>>>> the lens on till it loosely touches the first o-ring. Now turn the >>>>>> light >>>>>>>> on >>>>>>>>> for a few minutes. This will heat the lens and the head at the same >>>>>> time. >>>>>>>>> Once it is nice and warm, turn the light off and grasp the lens >>> with >>>> a >>>>>>>> towel >>>>>>>>> (or something of that nature) and push the lens in place. Once the >>>>>> whole >>>>>>>>> assembly cools, it will be in a vacuum state. Naturally, the head >>>>>>> material >>>>>>>>> needs to be such that it can be burned for a short time out of the >>>>>> water >>>>>>>> for >>>>>>>>> this "vacuum" method. >>>>>>>>> Aluminum and Delrin will have no problems with this. PVC or others >>>>>> would >>>>>>>> be >>>>>>>>> highly suspect. >>>>>>>>> Any high quality glass lens will have no problems either. The >>>> o-rings >>>>>> can >>>>>>>>> stand alot of heat as well. >>>>>>>>> >>>>>>>>> You should always pull a test tube style out of it's reflector >>>> before >>>>>>>> using, >>>>>>>>> just to check the seals. The lens can be hit in such a way that it >>>>>> cracks >>>>>>>>> the lens at the base, (where the o-rings are), but still appears to >>>> be >>>>>>>> just >>>>>>>>> fine while still in the reflector because this area is hidden from >>>>>> view. >>>>>>>>> Dell Motes >>>>>>>>> Dive Rite >>>>>>>>> 117 W.Washington St. >>>>>>>>> Lake City, Florida 32055 >>>>>>>>> www.dive-rite.com >>>>>>>>> >>>>>>>>> >>>>>>>>> -----Original Message----- >>>>>>>>> From: Paul Harris <paul.r.harris@te*.ne*> >>>>>>>>> To: 'Chris Elmore' <ElmoreC@gw*.sc*.ed*>; cmilz@Mi*.ED* >>>>>>> <cmilz@Mi*.ED*> >>>>>>>>> Cc: techdiver@aquanaut.com <techdiver@aquanaut.com>; >>>> cavers@ca*.co* >>>>>>>>> <cavers@ca*.co*> >>>>>>>>> Date: Wednesday, May 10, 2000 12:07 PM >>>>>>>>> Subject: RE: AUL canister light / light cord >>>>>>>>> >>>>>>>>> >>>>>>>>>> Chris, >>>>>>>>>> I'm not sure about this as a solution. >>>>>>>>>> Some friends and I were discussing non-wicking wire. >>>>>>>>>> My (humble) opinion is that you need some way of transfering >>>>>>>>>> air from the light head when you push the test tube on otherwise >>>>>>>>>> the positive pressure will push it off. >>>>>>>>>> >>>>>>>>>> I have noticed that it is much easier to remove or replace the >>>>>>>>>> test tube when the lid is off the cannister. >>>>>>>>>> >>>>>>>>>> r >>>>>>>>>> Paul >>>>>>>>>> >>>>>>>>>>> Claudia, >>>>>>>>>>> When I replaced my electrical cord I peeled the >>>>>>>>>>> insulation back from both ends (after cutting it to the right >>>>>>>>>>> length), put a wad of aquaseal around the wires, then pulled >>>>>>>>>>> the insulation back up. This will keep any water from getting >>>>>>>>>>> through a nick in the insulation and into the canister which >>>>>>>>>>> may be what's happening to yours. >>>>>>>>>>> C. >>>>>>>>>> >>>>>>>>>> -- >>>>>>>>>> Send mail for the `techdiver' mailing list to >>>>>> `techdiver@aquanaut.com'. >>>>>>>>>> Send subscribe/unsubscribe requests to >>>>>> `techdiver-request@aquanaut.com'. >>>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>>> >>>>> >>>>> >>>> >>>> >> >> -- >> Send mail for the `techdiver' mailing list to `techdiver@aquanaut.com'. >> Send subscribe/unsubscribe requests to `techdiver-request@aquanaut.com'. >> > > > -- Send mail for the `techdiver' mailing list to `techdiver@aquanaut.com'. Send subscribe/unsubscribe requests to `techdiver-request@aquanaut.com'.
Navigate by Author:
[Previous]
[Next]
[Author Search Index]
Navigate by Subject:
[Previous]
[Next]
[Subject Search Index]
[Send Reply] [Send Message with New Topic]
[Search Selection] [Mailing List Home] [Home]